Crown PIP-ISO Informações Técnicas descarregar pdf (Página 31)

Macro-Tech 600/1200/2400 Power Amplifiers

Page 31

Maximum Power Specifications

Crown’s maximum power specifications represent the largest amount of output power you can expect from your amplifier

when it is driven to full output under the given conditions. These specifications can be used to prevent loudspeaker and

hearing damage.

The maximum power matrices include specifications for single cycle and 40 millisecond burst sine waves. Burst signals act

like large transient peaks that are present in common source signals. Loudspeakers can respond to a single cycle burst, so

the single cycle burst specifications should be used to help you protect your loudspeakers. In contrast, a 40 millisecond burst

represents the typical response time of the human ear. Your ear will not respond to the entire dynamic change of a burst that

lasts less than 40 milliseconds.

The burst power specifications are provided at 0.05% THD which is a practical low distortion condition. Operating the ampli-

fier at levels higher than 0.05% THD can result in output power levels that are higher than those listed in the maximum power

matrices.

Stereo

(both channels

driven)

Bridge-Mono

(balanced output)

Parallel-Mono

460

350

255

820

700

510

905

765

520

450

375

260

945

745

520

880

740

525

Stereo

(both channels

driven)

Bridge-Mono

(balanced output)

Parallel-Mono

Macro-Tech 600 –

Maximum Power (Watts)

Stereo-Mono

Mode

40 Millisecond Tone Burst

At 0.05% THD

(See note 2)

Single Cycle Tone Burst

At less than 0.05% THD

(See note 1)

50 Hz 1 kHz

Load (Ohms)

20 Hz 50 Hz 1 kHz 7 kHz 7 kHz

AC Mains120 VAC, 60 Hz UnitsInternational Units

460

430

280

910

860

565

920

865

560

495

475

310

970

950

620

915

960

610

475

575

325

930

1165

655

940

1155

650

505

615

350

985

1240

700

930

1230

700

495

560

320

940

1130

640

970

1120

635

515

605

345

990

1210

680

970

1225

675

460

375

245

910

750

510

920

750

510

490

415

270

970

825

545

915

845

540

430

340

235

855

685

465

860

690

465

460

370

250

915

730

500

895

735

505

455

355

245

895

710

485

890

710

485

490

385

260

960

770

525

940

765

530

Fig. 6.4 Macro-Tech 600 Maximum Power Matrix

Maximum Power Notes:

All maximum power specifications are

based on 0.1% regulated AC mains

and an ambient room temperature of

70° F (21° C). International units with

multi-tap transformers are specified

for the best-case transformer tap (nor-

mally 240 VAC, 60 Hz). Although it is

an unusual condition, your amplifier

can function well with AC mains volt-

ages up to 10% over the specified line

voltage. With overvoltage conditions,

your amplifier may be capable of de-

livering instantaneous power levels up

to 20% greater than the specifications

in the matrix.

1. A single cycle sine wave is pre-

sented to the amplifier and moni-

tored for nonlinear distortion. The

average power during the burst is

reported. Loudspeakers must be

able to withstand this level if they

are to be safely used with this am-

plifier.

2. A 40 millisecond sine wave burst

(10 percent duty cycle) is pre-

sented to the amplifier and moni-

tored for nonlinear distortion. The

average power during the burst is

reported. This power level is a

measurement of the amplifier’s

maximum transient power that can

be perceived by the human ear.

1 2 ... 26 27 28 29 30 31 32 33 34 35 36 ... 42 43

Comentários a estes Manuais

Sem comentários

Crown PIP-ISO Informações Técnicas Página 31

Comentários a estes Manuais

Manuais e produtos relacionados com Equipamento de gravação Crown PIP-ISO