Crown II Manual do Utilizador descarregar pdf

Code No. 0816477

Rev. 0 (04/07)

INSTALLATION INSTRUCTIONS FOR PISTON TYPE FLUSHOMETER

EXPOSED CLOSET AND URINAL INSTALLATIONS

LIMITED WARRANTY

Sloan Valve Company warrants its Crown II

and Crown

Flushometers to be made of first class materials, free from defects of material or

workmanship under normal use and to perform the service for which they are intended in a thoroughly reliable and efficient manner when

properly installed and serviced, for a period of three years (1 year for special finishes) from date of purchase. During this period, Sloan Valve

Company will, at its option, repair or replace any part or parts which prove to be thus defective if returned to Sloan Valve Company, at

customer's cost, and this shall be the sole remedy available under this warranty. No claims will be allowed for labor, transportation or other

incidental costs. This warranty extends only to persons or organizations who purchase Sloan Valve Company's products directly from Sloan

Valve Company for purpose of resale.

THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT IS SLOAN VALVE COMPANY

RESPONSIBLE FOR ANY CONSEQUENTIAL DAMAGES OF ANY MEASURE WHATSOEVER.

PRIOR TO INSTALLATION

Before you install the Sloan Crown II and Crown

Flushometer, be sure the items listed below are

installed. Also, refer to the rough-in diagrams

below.

• Closet/urinal fixture

• Drain line

• Water supply line

Important:

• ALL PLUMBING SHOULD BE INSTALLED IN

ACCORDANCE WITH APPLICABLE CODES

AND REGULATIONS.

• WATER SUPPLY LINES MUST BE SIZED TO

PROVIDE AN ADEQUATE VOLUME OF WATER

FOR EACH FIXTURE.

• FLUSH ALL WATER LINES PRIOR TO MAKING

CONNECTIONS.

The Sloan Crown II and Crown Flushometer is

designed to operate with 10 to 100 psi (69 to

689 kPa) of water pressure. THE MINIMUM

PRESSURE REQUIRED TO THE VALVE IS

DETERMINED BY THE TYPE OF FIXTURE

SELECTED. Consult fixture manufacturer for

minimum pressure requirements. Most Low

Consumption water closets (1.6 gpf/6.0 Lpf)

require a minimum flowing pressure of 25 psi

(172 kPa).

TOOLS REQUIRED FOR

INSTALLATION

• Straight blade screwdriver

• Sloan A-50 Super-Wrench™, Sloan A-109

Plier Wrench or smooth jawed spud wrench

Closet Flushometer

for 1½” Back Spud

Crown II & Crown 120

VALVE ROUGH-IN

Urinal Flushometer

for 1¼” Top Spud

Crown II & Crown 180

Urinal Flushometer

for ¾” Top Spud

Crown II & Crown 186

Closet Flushometer for

1½" Top Spud

Crown II & Crown 111

Crown II & Crown 115

Crown II & Crown 116

MODEL 111 MODELS 115 & 116 MODEL 120

MODEL 180 MODEL 186

Flushometers

Made in the U.S.A.

1 2 3 4 5 6

Resumo do Conteúdo

Página 1 - VALVE ROUGH-IN

Code No. 0816477Rev. 0 (04/07)INSTALLATION INSTRUCTIONS FOR PISTON TYPE FLUSHOMETEREXPOSED CLOSET AND URINAL INSTALLATIONSLIMITED WARRANTYSloan Valve

Página 2

21Install Optional Sweat SolderAdapter (only if your supply pipedoes not have a male thread)3Install Vacuum Breaker FlushConnection2Install Cover Tube

Página 3 - Flush Out Supply Line

34Install Flushometer5Install Handle AssemblyCAlign Flushometer Body and securely tighten first the TailpieceCoupling (1), then the Vacuum Breaker Cou

Página 4 - TROUBLESHOOTING GUIDE

4CARE AND CLEANING OF CHROME ANDSPECIAL FINISHESDO NOT use abrasive or chemical cleaners (including chlorine bleach) to cleanFlushometers that may dul

Página 5 - 1-847-233-2016

When assistance is required, please contact Sloan Valve CompanyInstallation Engineering Department at:1-888-SLOAN-14 (1-888-756-2614)OR1-847-233-2016(

Página 6 - PARTS LIST

Item Part DescriptionNo. No.1 † Valve Assembly2 B-30-A Handle Assembly3A CR-120 PB (Polished Brass) Cover Trim Ring (Crown II only)CR-120 GP (Gold Pla

Comentários a estes Manuais

Sem comentários

Crown II Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Microfones Crown II. Crown Installation Instructions Manual do Utilizador

Resumo do Conteúdo

Comentários a estes Manuais

Manuais e produtos relacionados com Microfones Crown II